Olympia Chimney Chimney Cap Installation Nationwide

Olympia Chimney Chimney Cap Installation: The Fort Worth Owner’s Guide

If you’ve got an Olympia Chimney cap that’s rusted through, lost a spark screen, or started letting rain into the flue, we stock and install Olympia Chimney-compatible caps throughout Fort Worth, and most installations run between $275 and $475 fully installed, depending on the cap size and flue configuration. We keep common Olympia Chimney sizes on the truck, so in most cases we can complete the swap the same day we come out. You’ve probably noticed the problem either after a hard North Texas storm, when you saw water staining near the firebox, or when you spotted rust flakes in the yard after a windy week.

Call (682) 382-9934

Which Olympia Chimney Models This Applies To

Olympia Chimney makes caps that fit their round and oval rigid and flexible liner systems, with the most common Fort Worth installations being for 6-inch and 8-inch round flues, plus multi-flue caps for wider masonry crowns. The easiest way to identify what you have is to check the metal tag or etching on the cap itself, or measure the outside diameter of the flue tile or liner and match it to Olympia’s listed size. Here’s the compatibility gotcha we run into constantly: a 6-inch insulated liner typically requires a cap sized for a 6.5-inch or 7-inch outside diameter, not a 6-inch cap, because the insulation adds width. We’re an independent service provider and not affiliated with Olympia Chimney, but we stock both OEM Olympia caps and quality equivalents that match the locking band and mesh spec; for pre-2015 Olympia cap models that used a twist-lock collar, a good-quality aftermarket cap is often the smarter spend.

Signs Your Olympia Chimney Chimney Cap Installation Is Failing

• Water staining on the firebox floor or walls. This usually means the cap’s rain skirt or the seal at the flue collar has failed, letting water track straight down the flue. Left alone, it rusts out dampers and cracks mortar joints.
• Rust flakes or drip marks on the chimney crown. Fort Worth’s freeze-thaw cycles in December through February are rough on caps, and once the protective coating breaches, the steel underneath rusts fast.
• Animals in the flue. A missing spark screen or a bent side mesh is an open door for chimney swifts, squirrels, and raccoons, all of which are common in older Fort Worth neighborhoods with mature trees.
• Embers or debris landing on the roof. If the screen has gaps, you’ll see charred bits on the shingles after a fire. That’s a fire-safety issue we treat as urgent.
• Wind noise or a rattling cap. Loose locking bands or a bent base ring can make the cap shift in the gusts that move through the Trinity River corridor, and a cap that shifts is a cap that will eventually lift off.

For a free estimate and honest advice on whether the cap can be resecured or needs a full swap, call Fort Worth’s trusted chimney team at (682) 382-9934.

Replacement Cost & What’s Included

In Fort Worth, you’ll typically pay between $275 and $475 for a complete Olympia Chimney chimney cap installation, which includes the cap itself, the labor, a new locking band or base plate, and sealing of the flue collar. The spread comes down to three things: whether you need a stock 6-inch or 8-inch round cap (the low end) versus a custom multi-flue or oversized cap (the high end), whether the existing collar is still sound, and whether we need to do any minor crown repairs before setting the new cap. On the labor side, most installs take 30 to 60 minutes because we’re working from a ladder or the roof edge, and our techs bring the cap, the bands, and the high-temperature sealant with them. Each quote is a written price before any work starts, and if anything’s not right when we’re done, the 365-Day Done Right Promise means we come back and make it right.

DIY or Call Us?

You can safely inspect your cap from the ground with binoculars or a phone camera: check for rust, bent mesh, or missing screws, and if the flue is cool, you can look up from inside the firebox to see if the cap’s seated straight. What you shouldn’t do is get on a roof to swap a cap yourself, especially on Fort Worth’s steep-pitch rooflines in neighborhoods like Fairmount or Ryan Place. A chimney cap sits right at the roof edge, and a fall from even a single-story roof can change a family’s life. Climbing a ladder while carrying a metal cap in a wind gust is a two-person job with the right fall protection, and getting the seal wrong means water damage you won’t see until months later. If you want it done once and done right without putting yourself on a ladder, call us at (682) 382-9934.

FAQs